Guide to Machining and Fabricating A2 Tool Steel

Need Annealed A2 Ready to Machine?

Aobo Steel supplies A2 in annealed condition at around 200 to 235 HB for clean machining before hardening. Send your sizes and quantity, or see full product details.

Send Inquiry View A2 Tool Steel Details

Machining Strategies and Cutting Parameters of A2 Tool Steel

A2 is a medium-alloy cold work tool steel. In the annealed condition, approximately 200–235 HB, it can be machined using conventional methods. However, once hardened, its high volume of chromium carbides makes the material highly abrasive, rapidly increasing tool wear and machining difficulty.

Recommended starting cutting speeds for annealed A2 are shown below. These values should be adjusted for machine rigidity, cutting-tool grade, coolant condition, workholding, and part geometry.

A2 Tool Steel Machinability vs O1, H13, and D2

Machinability ratings are typically evaluated in the annealed condition and benchmarked against W1 tool steel at 100%.

Machinability vs Grindability

Machinability refers to cutting performance in the annealed state. Grindability refers to material removal after hardening.

Drilling and Grinding of A2 Tool Steel

For general drilling, standard high-speed steel drills are sufficient. For higher productivity or batch production, cobalt or carbide drills are recommended.

A2 has a strong tendency to work harden. During drilling, maintain continuous feed and avoid dwell. Any interruption allows the hole surface to harden, making further machining difficult.

Grinding must be carefully controlled. Excessive heat can locally temper or re-harden the surface, forming brittle untempered martensite and leading to grinding cracks. Use controlled passes and apply coolant consistently. For heavily ground components, stress relief treatment is recommended after grinding.

Welding Process for A2 Tool Steel

A2 can be welded, but its air-hardening characteristics create a high risk of cracking if procedures are not properly controlled.

Before welding, prepare the crack into a U-shape to reduce stress concentration. The workpiece must be preheated to approximately 800–900°F (427–482°C) and maintained at that temperature during welding.

After welding, allow the part to cool slowly to about 200°F (95°C), then immediately temper or stress-relieve to reduce the risk of cracking.

Filler material selection depends on the objective:

• For heat-treated parts, use a matching A2 composition.
• For repair or buffer layers, Type 312 stainless steel is commonly used.

The Impact of A2 Tool Steel Heat Treatment on Manufacturing

A2 is typically supplied in the annealed condition, with a ferritic matrix and spheroidized carbides, providing optimal machinability.

If the material has been cold-worked or hardened, it must be reannealed before machining. The typical annealing process includes:

• Heating to 1650°F (899°C).
• Holding for 2 hours per inch of thickness.
• Furnace cooling at no more than 50°F/hour down to 900°F (482°C).
• Air cooling to room temperature.

This restores hardness to approximately 235 HB, allowing proper machining.

After hardening, typically by air cooling from about 1775°F (968°C), A2 reaches 63–65 HRC. At this hardness level, conventional machining is no longer practical. Final sizing must be achieved through grinding or EDM.

When using EDM, a brittle recast “white layer” forms on the surface. This layer contains high residual stress and must be completely removed by polishing or grinding. A stress-relief tempering cycle should follow immediately to prevent microcracking.

Frequent Challenges and Solutions

1. Work Hardening

Work hardening is one of the most common machining issues with A2. If the tool is dull or the cut is too light, surface rubbing occurs instead of cutting, forming a hardened layer that blocks further tool penetration.

Solution: use sharp tools and maintain a consistent, positive feed. Avoid light cuts and surface rubbing.

2. Dimensional Distortion

Although A2 offers better dimensional stability than water-hardening steels, distortion still occurs during heat treatment. Typical expansion is about 0.001 inch per inch.

Solution: leave sufficient machining allowance before heat treatment to compensate for dimensional change and to remove decarburized layers during finishing.

3. Grinding Cracks

Grinding cracks occur when thermal stress exceeds the material’s strength, especially in hardened A2.

Solution: use soft, open-structure grinding wheels and apply coolant continuously. For welded or heavily ground parts, perform an additional stress-relief temper at 25–50°F (14–28°C) below the original tempering temperature.

Common Mistakes When Machining A2 Tool Steel

Understanding typical machining challenges is only the first step. In practice, most premature failures of A2 tools stem from avoidable process errors that introduce residual stresses, microcracks, or unstable microstructures during manufacturing.

1. Improper EDM Practices

Mistake: using EDM without proper finishing and leaving the as-EDM surface intact.

Consequence: EDM generates a brittle recast “white layer” with high residual stress and microcracks. Under service load, these cracks propagate rapidly, leading to chipping or catastrophic failure.

Solution: use fine finishing parameters, such as low current and high frequency, to minimize the depth of damage. Remove the white layer completely by grinding or polishing, followed by stress-relief tempering at 15–25°C (25–45°F) below the original tempering temperature.

2. Aggressive or Uncontrolled Grinding

Mistake: removing excessive material in one pass, using hard or loaded grinding wheels, or applying insufficient coolant.

Consequence: excessive heat leads to surface damage. Subcritical heating causes overtempering and soft spots, while overheating followed by rapid cooling forms brittle, untempered martensite. Both conditions create surface stresses that result in grinding cracks and reduced tool life.

Solution: use soft, open-structure grinding wheels with continuous coolant. Apply light passes and allow sufficient cooling between operations. For heavily ground parts, perform a stress-relief temper.

3. Allowing Tools to Rub (Work Hardening)

Mistake: using dull tools, low feed rates, or allowing the cutter to dwell and rub instead of cutting.

Consequence: surface work hardening occurs, forming a hardened layer that prevents further tool penetration and leads to rapid tool wear or breakage.

Solution: maintain sharp cutting tools and apply a consistent, positive feed rate. Ensure the tool is always cutting below the work-hardened layer. Avoid conventional center punching; use a tripod punch when marking drilling locations.

4. Sharp Corners and Poor Surface Finish

Mistake: leaving sharp internal corners, deep machining marks, or rough surfaces before heat treatment.

Consequence: these features act as stress concentrators. During quenching, thermal stress localizes at these points, often causing cracking. Even if cracking does not occur during heat treatment, fatigue failure is likely in service.

Solution: use generous fillets and smooth transitions. Remove deep machining marks and avoid sharp edges. Apply finishing processes to reduce surface stress concentration before hardening.

5. Insufficient Stock Removal (Decarburization Layer)

Mistake: machining too close to the original hot-rolled surface without removing the decarburized layer.

Consequence: the surface remains low in carbon and cannot achieve full hardness. This creates a soft outer layer and increases the risk of uneven transformation and cracking during heat treatment.

Solution: always machine away the decarburized “bark.” As a general rule, remove approximately 1/16 inch, or 5–10% of the section size, from all surfaces to ensure consistent material properties.

6. Skipping Stress Relief After Heavy Machining

Mistake: sending heavily machined parts directly to hardening without stress relief.

Consequence: residual machining stresses are released during heating, causing distortion such as warping or twisting, which leads to dimensional instability and scrap.

Solution: perform subcritical stress-relief annealing after rough machining. Then complete the machining before final heat treatment.