Cr12MoV Takım Çeliği

AOBO STEEL – Trusted Global Tool Steel Supplier

Cr12MoV tool steel is a high-carbon, high-chromium ledeburite cold work tool steel with high hardness, wear resistance, and minimal quenching deformation. This steel grade is an improved version of Cr12 tool steel, with the addition of molybdenum (Mo) and vanadium (V) elements to enhance its performance characteristics.

1. Composition of Cr12MoV Steel（GB/ T 1299—2000）

C	Si	Mn	Cr	V	Ay	S	P
1.45 ~ 1.70	≤0,40	≤0,40	11.00 ~ 12.50	0.15 ~ 0.30	0.40 ~ 0.60	≤0.030	≤0.030

2. Properties of Cr12MoV Steel

Critical Point Temperature

Kritik Nokta	Ac₁	Ac₃	Ar₁	Bayan
Temperature (approx.) / °C	810	1200	760	185

Doğrusal Genleşme Katsayısı

Sıcaklık / °C	Linear Expansion Coefficient α / (10⁻⁶ °C⁻¹)
20 ~ 100	10.9
20 ~ 400	11.4
20 ~ 600	12.2

Cr12MoV is a high-carbon, high-chromium, high-hardenability ledeburitic steel. It is characterized by high hardness, good impact toughness, high hardenability, and low distortion upon quenching.

For cross-sectional dimensions up to 400mm, it can be fully through-hardened. Furthermore, it maintains good hardness and wear resistance at elevated temperatures in the range of 300 ~ 400°C.

With minimal volumetric change during quenching and excellent overall mechanical properties, Cr12MoV is considered one of the representative steel grades for high-end cold work tooling materials.

3. Forging Process Specification of Cr12MoV Steel

Öğe	Heating Temp. / °C	Initial Forging Temp. / °C	Final Forging Temp. / °C	Soğutma Yöntemi
Ingot	1100 ~ 1150	1050 ~ 1100	850 ~ 900	Slow cooling (pit or sand cooling)
Kütük	1050 ~ 1100	1000 ~ 1050	850 ~ 900	Slow cooling (pit or sand cooling)

Note: Cr12MoV steel has a low melting point, so the heating temperature should not be too high; it has poor thermal conductivity, so attention should be paid to slow heating. After forging, it must be cooled slowly to avoid cracks. It can be placed in a preheated pit and cooled to 400-500°C. Annealing can be performed after cooling.

Please fill out the following form to contact us now！

4. Isıl İşlem

4.1 Ön ısıtma

	İşlem Parametreleri
Post-Forging Annealing	Heating temperature 850 ~ 870°C, hold for 1 ~ 2h, furnace cool to below 500°C then air cool. Hardness after annealing is 207 ~ 255HBW, microstructure is fine pearlite + carbide.
Post-Forging Isothermal Annealing	Heating temperature 850 ~ 870°C, hold for 1 ~ 2h, furnace cool to 720 ~ 750°C, hold for 3 ~ 4h, furnace cool to below 550°C then air cool. Hardness after annealing is 207 ~ 255HBW. Microstructure is fine pearlite + carbide.
High-Temperature Tempering	Heating temperature 760 ~ 790°C, hold for 2 ~ 3h, furnace cool or air cool. Hardness is 207 ~ 255HBW.

4.2 Söndürme

Quenching Process Specifications for Cr12MoV Steel

Şema	1st Preheating Temp./°C	2nd Preheating Temp./°C	Quenching Temp./°C	Söndürme Ortamı	Quenching Medium Temp./°C	Cooling in Medium	Subsequently	Sertlik HRC
BEN	550 ~ 600	840 ~ 860	950 ~ 1000	Yağ	20 ~ 60	To oil temp	Hava soğutma	58 ~ 62
II			1020 ~ 1040	Yağ	20 ~ 60	To oil temp	Hava soğutma	62 ~ 63
III			1020 ~ 1040	Molten nitrate salt	400 ~ 550	5 ~ 10min	Hava soğutma	62 ~ 63
IV			1115 ~ 1130	Yağ	20 ~ 60	To oil temp	Hava soğutma	42 ~ 50
V			1115 ~ 1130	Molten nitrate salt	400 ~ 450	5 ~ 10min	Hava soğutma	42 ~ 50

Note: Schemes IV and V are used for molds that require hot hardness and high wear resistance, such as hot stamping dies working below 450°C, but their mechanical properties are poor, and dimensional deformation is large. After quenching according to schemes I and II, the volume fraction of the microstructure is 12% carbides, 68% to 73% martensite, and 20% to 25% retained ostenit.

Hardness and Quenching Temperature Under Different Heating and Cooling Conditions

Heating Conditions	Soğutma Yöntemi	Quenching Temp./°C	Sertlik HRC
Heating in carburizing agent	Oil cooling	930	64
		980	65
		1010	65
		1030	63.5
Heating in air furnace	Oil cooling	930	60.2
		980	63
		1010	63.9
		1030	63.5
Heating in air furnace	Hava soğutma	930	59
		980	62.5
		1010	63.2
		1030	62

4.3 Temperleme

Tempering Process Specifications

Şema	Quenching Temp./°C	Tempering Purpose	Tempering Temp./°C	Orta	Sertlik HRC
BEN	1020 ～ 1040	Stress relief	150 ~ 170	Oil or nitrate salt	61 ~ 63
II		Stress relief, reduce hardness	200 ~ 275	—	57 ~ 59
III		Stress relief, reduce hardness	400 ~ 425	—	55 ~ 57
IV	1115 ~ 1130	Stress relief and secondary hardening	510 ~ 520℃ Multiple tempering	—	60 ~ 61
V			-78℃ Cryogenic treatment + 510 ~ 520℃ single tempering	—	60 ~ 61
VI			-78℃ Cryogenic treatment plus one 510 ~ 520℃ tempering, then another -78℃ cryogenic treatment	—	61 ~ 62

Not:

Workpieces tempered according to Scheme I need to maintain high hardness and high wear resistance, and their dimensional changes are almost independent of the quenching state.
Scheme II is used to obtain workpieces with good toughness.

Tempering Temperature and Hardness

Tempering Temp./°C	Untempered	100	200	300	400	500	550	600	650
Sertlik HRC	63	62	61	59	57	59	53	47	40

Not: Oil quenched at 1030°C, tempered for two hours.

5. Uygulamalar

Cr12MoV steel is suitable for manufacturing a wide variety of tools and dies that are characterized by large cross-sections, complex shapes, and are subjected to significant impact loads. Examples of such applications include:

Punching dies with complex geometries
General stamping dies
Blanking dies for silicon steel sheets
Kırpma kalıpları
Edge rolling/curling dies
Tel çekme kalıpları
Soğuk ekstrüzyon kalıpları
Deep drawing dies for steel plate
İplik haddeleme plakaları
Cold shearing blades
Circular saws
Standart aletler ve ölçü aletleri

Your Premier Source for Cr12MoV Tool Steel

Leverage our 20+ years of expertise. We supply high-quality Cr12MoV tool steel, a versatile cold-work steel known for its excellent toughness, wear resistance, and dimensional stability. Contact our specialists for detailed specifications and a competitive quote.

Uzman Rehberliği

Piyasa Lideri Fiyatlar

Ürünlerimiz

Diğer Ürünlerimizi Keşfedin

D2/1.2379/SKD11

D3/1.2080/SKD1

D6/1.2436/SKD2

A2/1.23663/SKD12

O1/1.2510/SKS3

O2/1.2842

S1/1.2550

S7/1.2355

DC53

H13/1.2344/SKD61

H11/1.2343/SKD6

H21/1.2581/SKD7

L6/1.2714/SKT4

M2/1.3343/SKH51

M35/1.3243/SKH55

M42/1.3247/SKH59

P20/1.2311

P20+Ni/1.2738

420/1.2083/2Cr13

422 paslanmaz çelik

52100 rulman çeliği

440C paslanmaz çelik

4140/42CrMo4/SCM440

4340/34CrNiMo6/1.6582

4130

5140/42Cr4/SCR440

SCM415