{"id":13830,"date":"2026-03-17T10:51:05","date_gmt":"2026-03-17T02:51:05","guid":{"rendered":"https:\/\/aobosteel.com\/?page_id=13830"},"modified":"2026-03-18T11:14:11","modified_gmt":"2026-03-18T03:14:11","slug":"h13-die-failure-identification","status":"publish","type":"page","link":"https:\/\/aobosteel.com\/es\/h13-die-failure-identification\/","title":{"rendered":"H13 Die Failure Identification | Aobo Steel Tool Steel Supplier"},"content":{"rendered":"
\n

C\u00f3mo identificar fallas en el chip H13<\/h1>\n\n\n\n

H13 die failure typically shows up in three practical ways: loss of dimensional accuracy, surface damage that affects part quality, or sudden cracking and fracture.<\/p>\n\n\n\n

In real production, the key question is not whether wear exists, but whether the die fails earlier than expected or begins to lose dimensional control during operation.<\/p>\n\n\n\n

This article explains how heat checking develops in H13 dies and describes the engineering and operational practices that can slow its progression. For a broader overview of failure mechanisms in this steel, see the Gu\u00eda de an\u00e1lisis de fallos H13<\/a>.<\/p>\n\n\n\n

Step 1 \u2013 Classify the Failure Mode by Visible Damage<\/h2>\n\n\n\n

Accurate diagnosis always starts with what you can actually see on the tool surface or in the fracture area. Different damage patterns point to different mechanisms.<\/p>\n\n\n\n

Fatiga t\u00e9rmica (comprobaci\u00f3n de calor)<\/h3>\n\n\n\n

This is the most common failure mode in hot-work dies.<\/p>\n\n\n\n

It appears as a network of fine, shallow cracks forming a grid-like or crazed pattern. These cracks are typically limited to the surface and are found in areas exposed to repeated heating and cooling.<\/p>\n\n\n\n

The underlying cause is cyclic thermal expansion and contraction under temperature fluctuations.<\/p>\n\n\n\n

Gross Cracking (Fracture)<\/h3>\n\n\n\n

This type of failure is much more severe and usually happens suddenly.<\/p>\n\n\n\n

It presents as large, deep cracks or a complete fracture of the die. In most cases, the applied stress exceeds the material’s fracture toughness.<\/p>\n\n\n\n

Erosion and Softening<\/h3>\n\n\n\n

Erosion and softening often appear together, but should be understood separately.<\/p>\n\n\n\n

Erosion, also called washing, is seen as localized material loss. It is most common in areas where molten metal flows at high velocity, such as gates and runners.<\/p>\n\n\n\n

Softening occurs when the operating temperature exceeds the original tempering temperature. The steel loses strength, which leads to plastic deformation or gradual distortion of the cavity.<\/p>\n\n\n\n

Chemical Attack and Abrasive Wear<\/h3>\n\n\n\n

In aluminum die casting, chemical attack usually appears as soldering. Molten aluminum adheres to the die surface and can damage it during ejection.<\/p>\n\n\n\n

Abrasive wear is different. It shows up as scratches or grooves and is commonly seen in forging, where oxide scale is pressed against the die under high load.<\/p>\n\n\n\n

Step 2 \u2013 Identify Failure by Appearance and Location<\/h2>\n\n\n\n

A reliable diagnosis always combines what the damage looks like with where it occurs.<\/p>\n\n\n\n

Appearance Indicators<\/h3>\n\n\n\n

Fatigue cracks often show beach marks or striations, which indicate progressive crack growth.<\/p>\n\n\n\n

A bright, faceted fracture surface usually points to brittle or intergranular fracture.<\/p>\n\n\n\n

If blue or brown temper colors are visible near a crack, it indicates that the crack already existed before or during tempering.<\/p>\n\n\n\n

Location Indicators<\/h3>\n\n\n\n

Damage on working surfaces is typically linked to thermal fatigue.<\/p>\n\n\n\n

Material loss near gates and runners usually indicates erosion.<\/p>\n\n\n\n

Cracks at sharp corners or in thin sections often result from stress concentrations.<\/p>\n\n\n\n

Failures in EDM-machined areas should always raise suspicion of an unremoved white layer.<\/p>\n\n\n\n

Step 3 \u2013 Distinguish the Root Cause<\/h2>\n\n\n\n

After identifying the failure type, the next step is to determine why it happened. This requires separating process factors, heat treatment issues, and material-related causes.<\/p>\n\n\n\n

Process-Related Causes<\/h3>\n\n\n\n

In most real industrial cases, process-related factors are the main drivers of failure.<\/p>\n\n\n\n

Poor lubrication can lead to localized wear. Severe thermal cycling accelerates heat checking. Excessive load can push the die into plastic deformation.<\/p>\n\n\n\n

These issues are usually repeatable and tied to operating conditions.<\/p>\n\n\n\n

Heat Treatment Causes<\/h3>\n\n\n\n

Heat treatment problems often show up as abnormal fracture behavior.<\/p>\n\n\n\n

If tempering is too low, the die may retain excessive hardness but lack toughness, increasing the risk of brittle fracture.<\/p>\n\n\n\n

If the austenitizing temperature is too high, grain boundary embrittlement can occur.<\/p>\n\n\n\n

Improper quenching can introduce cracks that exist even before tempering.<\/p>\n\n\n\n

Material and Manufacturing Causes<\/h3>\n\n\n\n

Material-related problems are less frequent but more critical when they occur.<\/p>\n\n\n\n

Common issues include stress concentrators such as sharp radii, deep stamp marks, or machining grooves.<\/p>\n\n\n\n

An unremoved white EDM layer is another common cause. This layer consists of brittle untempered martensite with microcracks and can act as an initiation point for failure.<\/p>\n\n\n\n

Internal defects such as coarse carbides or nonmetallic inclusions may also trigger subsurface cracking.<\/p>\n\n\n\n

These types of failures are usually associated with early failure or internal crack origins, rather than gradual surface wear.<\/p>\n\n\n\n

Step 4 \u2013 Quick Diagnostic Table<\/h2>\n\n\n\n
Visible Symptom<\/td>Typical Location<\/td>Causa probable<\/td><\/tr>
Fine crack network<\/td>Working surface<\/td>Thermal fatigue (heat checking)<\/td><\/tr>
Washed-out features<\/td>Gates, runners<\/td>Erosion from molten metal flow<\/td><\/tr>
Faceted brittle fracture<\/td>Thick sections<\/td>Heat treatment embrittlement<\/td><\/tr>
Crack with temper color<\/td>Corners, holes<\/td>Crack formed before tempering<\/td><\/tr>
Crack at EDM surface<\/td>Machined cavities<\/td>Unremoved white layer<\/td><\/tr>
Crack at notch<\/td>Sharp radii, stamps<\/td>Stress concentration<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

When to Suspect a Material Problem<\/h2>\n\n\n\n

Material should only be considered the primary cause under specific conditions. This includes cases in which failure occurs much earlier than expected, cracks originate below the surface, or properties are inconsistent across the section. It is also relevant when the fracture origin is clearly linked to inclusions or carbide segregation. In most practical situations, failures originate from process conditions or heat treatment rather than the steel itself.<\/p>\n\n\n\n

Practical Guidance to Avoid Misdiagnosis<\/h2>\n\n\n\n

Misdiagnosis is common and often leads to the wrong corrective actions. Fracture surfaces should always be preserved and not reassembled. The origin of the crack must be inspected before any cutting or sectioning is done. The die design should be checked for stress concentrators such as sharp corners or deep markings. EDM areas must be verified to ensure the white layer has been properly removed. Most importantly, process conditions and heat treatment should be evaluated first before concluding that the material is the root cause.<\/p>\n\n\n\n